What Is 18.25 MΩ·cm Ultra Pure Water — and Why Does It Matter?

Water quality is measured by its electrical resistivity — the higher the value, the fewer the dissolved ions and contaminants. At 18.25 MΩ·cm at 25 °C, water reaches its theoretical maximum purity, meaning virtually all dissolved salts, organics, particles, and microorganisms have been removed.

This level of purity is not merely a marketing claim. It is the internationally recognised standard for Type I ultrapure water as defined by ASTM D1193, ISO 3696 Grade 1, and CLSI C3-A4. Applications that depend on this quality include:

  • Analytical chemistry & HPLC — solvent preparation, mobile-phase dilution, blank matrix
  • Cell biology & molecular biology — PCR, cell culture media, buffer preparation
  • Semiconductor manufacturing — wafer rinsing, photolithography cleaning baths
  • Pharmaceutical quality control — reagent preparation, equipment rinsing, WFI support
  • Electronics testing — printed circuit board washing, battery electrolyte research

Any contamination in feed water introduces ionic interference, alters reaction kinetics, and potentially damages sensitive instruments. Choosing the right water purification system is therefore a critical infrastructure decision, not merely a procurement exercise.

Two-Stage Reverse Osmosis + EDI: The Gold-Standard Process

Reaching 18.25 MΩ·cm consistently requires a multi-barrier purification train. The most reliable commercial architecture for 0.5 TPH output is a two-stage reverse osmosis system followed by an electrodeionization (EDI) polishing module. Here is how each stage contributes:

Tap / Feed Water
→
Multimedia Filter
→
Activated Carbon
→
Softener
→
5 µm Cartridge
→
RO Stage 1
→
RO Stage 2
→
EDI Module
→
SS Aseptic Tank
→
18.25 MΩ·cm Output

Stage 1 – Pre-Treatment

A multimedia filter removes turbidity and suspended solids; an activated carbon block adsorbs chlorine, chloramine, and organic compounds that would degrade RO membranes. A water softener (or antiscalant dosing) prevents calcium and magnesium scaling. A final 5-micron cartridge filter acts as a guard for the membrane elements.

Stage 2 – First-Pass Reverse Osmosis

High-pressure pump forces feed water across a semi-permeable polyamide TFC membrane. RO Stage 1 typically rejects 96–98% of total dissolved solids (TDS), bacteria, viruses, and endotoxins. Permeate conductivity drops from hundreds of µS/cm to single-digit µS/cm.

Stage 3 – Second-Pass Reverse Osmosis

The Stage 1 permeate is re-pressurised and passed through a second set of RO membranes. This second pass achieves conductivity below 1 µS/cm (resistivity > 1 MΩ·cm) and brings CO₂ levels low enough for EDI to function efficiently. Twin-pass RO also dramatically extends EDI module lifetime.

Stage 4 – Electrodeionization (EDI)

EDI is the breakthrough technology that enables continuous production of ultrapure water without chemical regeneration. Ion-exchange resins sitting between ion-selective membranes are continuously regenerated by a low-voltage DC electric field that splits water into H⁺ and OH⁻. The result: consistent 16–18.25 MΩ·cm resistivity output with no acid/caustic consumption and no regeneration downtime.

Stage 5 – Stainless Steel Aseptic Storage Tank

Ultrapure water is highly aggressive and will rapidly absorb CO₂ from air and leach metals from ordinary storage vessels. Our system uses a 316L stainless steel tank with a hydrophobic PTFE vent filter, internal electropolished surface (Ra ≤ 0.4 µm), and a UV lamp port to maintain microbial quality in the distribution loop.

Technical Specifications at a Glance

ParameterSpecificationStandard Reference
System Capacity0.5 m³/h (0.5 TPH)—
Output Water Quality≥ 18.25 MΩ·cm @ 25 °CASTM D1193 Type I
TOC (Total Organic Carbon)< 10 ppbISO 3696 Grade 1
Bacteria (viable count)< 0.1 CFU/mLISO 3696 Grade 1
Particles ≥ 0.2 µm< 1 particle/mLSEMI F57
Silica< 3 ppbASTM D5544
Pre-treatmentMultimedia + Carbon + Softener + 5 µm cartridge—
RO ArchitectureTwo-stage, high-rejection TFC membranes—
EDI ModuleContinuous electrodeionization, no chemical regeneration—
Storage Tank316L SS, electropolished, PTFE vent filter—
Operating Pressure0.3 – 0.5 MPa—
Feed Water TDS≤ 2,000 ppm—
Power Supply380 V / 50 Hz / 3-phase (custom available)—
Skid FootprintCompact, CE-compliant skid-mounted—

Key Advantages of the Yufeng 0.5TPH RO+EDI System

  • No chemical regeneration required — Traditional deionisation (DI) beds must be taken offline and regenerated with sulphuric acid and sodium hydroxide. EDI eliminates this cost, downtime, and chemical handling risk entirely.
  • Continuous, stable output — EDI produces ultrapure water 24 / 7 at consistent quality. There is no "exhaustion curve" as with mixed-bed resins.
  • Lower long-term operating cost — Reduced consumable spend on regenerant chemicals, reduced waste treatment cost, and lower labour overhead from eliminating manual resin regeneration cycles.
  • Compact, skid-mounted design — The entire treatment train is pre-assembled, piped, wired, and tested in our factory before shipment. On-site installation time is typically one day.
  • Stainless steel aseptic tank included — Many competitors supply ultrapure water systems without compliant storage. Our complete solution includes a 316L SS tank with UV sterilisation provision.
  • PLC monitoring and alarm system — Resistivity, conductivity, flow, pressure, and temperature readings are displayed on a touch-screen HMI with configurable alarm thresholds.
  • International technical support — WhatsApp direct contact with our engineering team for rapid commissioning assistance and troubleshooting guidance.

Who Should Choose a 0.5 TPH System?

The 0.5 TPH (500 L/h) output tier is ideal for:

  • University research laboratories with multiple analytical instruments sharing a single purification point
  • Small-to-medium pharmaceutical QC labs requiring USP Purified Water plus a polished ultra-pure stream
  • Pilot-scale semiconductor and display panel cleaning baths
  • Electroplating and precision metal finishing facilities
  • Industrial boiler feed water pre-treatment in facilities with moderate steam demand
  • Cosmetics and personal care manufacturing where ion-free water is specified in GMP protocols

If your usage exceeds 0.5 TPH, Yufeng Water Treatment manufactures systems from 0.25 TPH to 50+ TPH and can configure parallel trains for redundancy and capacity expansion.

Frequently Asked Questions

Q1. What feed water quality does this system require?
The system is designed for municipal tap water with TDS up to 2,000 ppm. For brackish or high-hardness sources above this limit, additional pre-softening or an extra RO stage may be recommended. Contact our engineering team for a site-specific assessment.
Q2. How is EDI different from a mixed-bed deioniser?
Mixed-bed DI uses ion-exchange resins that gradually become exhausted and must be regenerated off-site with strong acids and caustics — creating downtime, chemical costs, and hazardous waste. EDI uses a continuous DC electric field to regenerate the resin in situ, requiring no chemicals and producing water continuously at consistent 18.25 MΩ·cm quality.
Q3. What maintenance does the system require?
Routine maintenance includes: replacing the 5 µm cartridge filter every 1–3 months; inspecting RO membranes annually (typical membrane life 3–5 years with good pre-treatment); UV lamp replacement once per year; and periodic sanitisation of the storage tank and distribution loop with heated water (85 °C) or chemical biocide.
Q4. How long does installation take?
Because the system is factory-assembled and tested on a single skid, on-site installation typically takes 4–8 hours. You will need a dedicated feed water connection, drain, floor drain for reject water, and a 380 V / 3-phase power supply.
Q5. Can the system be customised for different voltages or capacities?
Yes. We supply 220 V single-phase for smaller units, 380 V 3-phase for standard industrial configurations, and can adapt to 60 Hz North American supply. Output capacity can be scaled from 0.25 TPH to 50+ TPH. Custom skid dimensions, additional polishing steps (UV/TOC, ultrafiltration), and specific material certifications are available on request.
Q6. What certifications does the equipment carry?
The Yufeng RO+EDI system is designed and manufactured in compliance with CE marking requirements for the European market and meets GB/T standards for the domestic Chinese market. Custom documentation packages for FDA 21 CFR Part 11, USP <1231>, or SEMI F57 can be provided for pharmaceutical and semiconductor customers.

How to Order or Request a Quotation

Getting a precise quotation takes fewer than 24 hours. Please prepare the following information before contacting our sales team:

  1. Your feed water TDS (or a recent water analysis report)
  2. Required output volume per day or per hour
  3. Intended application (lab, pharma, semiconductor, industrial)
  4. Site country and power supply voltage / frequency
  5. Any special certifications or material requirements

Our engineers will review your requirements and return a detailed technical proposal, P&ID diagram, and itemised quotation — at no cost and with no obligation.

Ready to Get Laboratory-Grade 18.25 MΩ·cm Water?

Contact the Yufeng Water Treatment engineering team now for a free technical consultation and quotation within 24 hours.

Visit Our Website  💬 WhatsApp Us
#UltraPureWaterEquipment  #ReverseOsmosis  #EDI  #LaboratoryWater  #WaterTreatment  #TwoStageRO  #HighPurityWater  #WaterPurification  #18MΩ  #LabEquipment